Logitech Revue Technical

Specs

• Intel Atom CE4150 1.2 GHz processor, with a 400 MHz GPU
• Gigabyte GA-SBKAN2 motherboard
• Samsung K9F8G08U0M 1 GB NAND Flash (Single Level Cell) Datasheet Mirror
• Hynix H27UBG8T2ATR 4 GB NAND Flash (Multiple Level Cell)
• Silicon Image Sil9135 HDMI 1.3 Receiver Chip Information Datasheet from TI
• Nanya NT5CB128M8CN-CG 1 GB DDR3 SDRAM (1 Gb X 8) Datasheet
• Realtek Semiconductor RTL8201N 10/100M PHYceiver Datasheet
• Microchip PIC24FJ64GA004-I/PT 16-bit microcontroller Datasheet
• Phison S2251-50 USB to Flash Controller (Datasheet not available to end users according to manufacture)
• IDT ICS9LPRS525AGLF Clock for CPU Datasheet

The Logitech Revue was recently torndown and its inners revealed. Direct link to the higher resolution picture of the motherboard.

SemiAccurate has a populated board similar to the one in the Revue: http://www.semiaccurate.com/2010/06/04/gigabyte-has-google-tv-ready-motherboard/

Usage

Samsung K9F8G08U0M 1 GB NAND Flash

• Used for storage of bootloader, kernel, boot flash graphics, Linux OS etc..

Hynix H27UBG8T2ATR 4 GB NAND Flash (Long Term Storage)

• Used for persistent storage, device is /dev/sda - possible to override with an external USB drive

Microchip PIC24FJ64GA004-I/PT 16-bit microcontroller

• Used to handle IR input/output for remotes/IR blasters and possible interface with wireless keyboard
• System reboot/powerdown
• Possibly HDMI CEC

Silicon Image Sil9135 HDMI 1.3 Receiver

• Used to process video to and from HDMI ports as well as audio over HDMI and SPDIF
• Supports DTS even though the Revue does not (An update can probably enable this feature)

IDT ICS9LPRS525AGLF Clock for CPU

• Provides a clock for the Intel Atom CPU

Update Procedure

Place new update labeled "update.zip" on a USB drive, with a single partition (ie, 1st partition on a USB disk, so say "/dev/sdc1")

Insert into Revue in the Right most USB port (if looking at the back, closest to the power jack)

Boot into recovery mode: (confirm?)

1. Hold the Sync button while plugging in the Revue, keep it held, at the same time hold Menu+L on the keyboard.
2. Box will reboot, continue to hold Sync button, then hold Alt+L (or mash, your choice), and it should then enter recovery mode.
3. You can then update the box, with a newer update. Downgrading fails however due to a date check.

Firmware Links

http://android.clients.google.com/packages/ota/logitech_ka/439c26f6af05.mp-signed-ota_update-b39389.zip

http://android.clients.google.com/packages/ota/logitech_ka/52057d168e2b.mp-signed-ota_update-b39953.zip

http://android.clients.google.com/packages/ota/logitech_ka/c9914396d183.mp-signed-ota_update-b42449.zip

(Add update history?)

Flash Layout

via: http://googletv.pastebin.com/233dZqZx

Creating 13 MTD partitions on "intel_ce_nand":

• 0x00000000-0x00200000 : "mbr"
• 0x00200000-0x00a00000 : "cefdk"
• 0x00a00000-0x00c00000 : "redboot"
• 0x00c00000-0x00e00000 : "cefdk-config"
• 0x01000000-0x01800000 : "splash"
• 0x01800000-0x01900000 : "fts"
• 0x01900000-0x02d00000 : "recovery"
• 0x02d00000-0x03200000 : "kernel"
• 0x03200000-0x07200000 : "boot"
• 0x07200000-0x1f200000 : "system"
• 0x1f200000-0x3fa00000 : "data"
• 0x3fa00000-0x3ff00000 : "keystore"
• 0x3ff00000-0x40000000 : "bbt"

mbr - Master Boot Record

cefdk - Boot loader, may or may not have a shell

Splash - Splash image, can be seen here ( http://img413.imageshack.us/img413/3144/splashc.png )

Recovery - Full image, including kernel and small ramdisk (in squashfs format), boots to recovery menu

Kernel - The kernel image

Boot - Root partition, goes in hand with the kernel image, also in squashfs format

fts - Flash transactional key/value storage

bbt - Bad block table

system - yaffs

data - yaffs

Serial Output

The logitech revue board contains a UART1 port on the front of the board which before receiving the boxes initial updates is active. In order to communicate with UART port you will need a USB to TTL adapter (or board that does a similar conversion).

The pins operate at 3.3v and the port at 9600 baud with the following pinout:

UART Pinout

Serial output

via: http://googletv.pastebin.com/233dZqZx Pasted Locally

PIC Access

• There is a standard PIC access port to the right of the UART1 port. It can be accessed via a standard PIC Kit Debug board (Tested with version 2). The port has read/write access but the code is pulled from the chip as .hex file and is unreadable thus far.

• The pinout starting from the left (pin with white square around it) corresponds to pin 1 or Vpp.The remaining pins follow the same layout. PIC Pinout

PIC Hex Dump Local PIC Hex Dump

Updates

The updates contain a subset of update files, a boot.img and a recovery.img

boot.img & recovery.img

The thread at xda-developer has the process to extract from the .img files (thx bftb0):

"the "boot.img" file is in (little-endian) "squashfs" format and unpacks just fine using "unsquashfs" from the (Ubuntu 8.0.04 LTS) squashfs-tools package."

system/boot/recovery.img is a standard Android boot image with some extra garbage at the front.

 dd if=system/boot/recovery.img bs=1408 skip=1 > recovery-ungarbaged.img

Unpack that like a normal Android boot image. Something like this Perl script works well.

The kernel (system/boot/kernel) is also a boot image with the same extra garbage at the front.

Odex files

The .odex files can be extracted by using the following guide Deodex Instructions

Available Pinouts

• UART1 --> Uart Pinout
• J3 --> PIC Chip Access
• SW1 --> Push Button Switch (Use is unknown)
• J20 --> Unknown (May be JTAG)
• J69 --> USB Pinout
• SATA1 --> SATA pinout (may have power included, needs verification)
• J24 --> Unknown (may be power for SATA)
• J13 --> Power for another fan probably
• XDP1 --> Possibly a Intel XDP Debug Adapter Information on XDP Debugging